Slim Size Dali Dimmable LED Driver 60W (IP20)
SMT-012-060VMSP
DALI Dimmable LED Driver
SMARTS
VMSP series plastic case dali & push dimming 12v 5a 60W led driver dimmable power supply constant voltage output mode, UL certified, compliant with global safety lighting regulations can be use...
VMSP series plastic case dali & push dimming 12v 5a 60W led driver dimmable power supply constant voltage output mode, UL certified, compliant with global safety lighting regulations can be used for landscape lighting and architectural lighting projects.
| model | SMT-012-060VMSP | SMT-024-060VMSP | |
| Output | DC Voltage | 12VDC | 24VDC |
| Voltage Tolerance | ±0.5V | ±0.5V | |
| Rated current | 5.0Amp | 2.5Amp | |
| Rated power | 60W | 60W | |
| Voltage Regulation | ±0.5% | ||
| Load Regulation | ±2% | ||
| Input | Voltage Range | 100-277VAC | |
| Frequency Range | 47~63HZ | ||
| Power Factor(Typ.)@ full load | 0.98@120VAC | 0.98@120VAC | |
| Efficiency(Typ.)@ full load(Typ.) | >86% | >88% | |
| AC Current(Max.) | 0.73A@100VAC | ||
| THD(Typ. ) @ full load | 10%@120VAC | 10%@120VAC | |
| Inrush Current(Typ.) | 3A (twidth=220us) @120VAC ; 34A (twidth=121us) @230VAC ;12.4A (twidth=680us) @277VAC ; | ||
| Leakage current | <0.5mA | ||
| Protection | Short Circuit | shut down o/p voltage, re-power on to recover after fault condition removed | |
| Over Load | ≤120% Hiccup mode ,recovers automatically after fault condition is removed or shut down o/p voltage, re-power on to recover after fault condition removed | ||
| Protection Class | II | ||
| Over temperature | 100℃±10℃ shut down o/p voltage, automatically recover after cooling | ||
| Environment | Working TEMP. | -40~+60℃ (see below derating curve) | |
| Working Humidity | 20~95%RH,non-condensing | ||
| Storage TEM.,Humidity | -40~+80℃,10~95%RH | ||
| TEMP.coefficient | ±0.03%/℃(0~50℃) | ||
| Vibration | 10~500Hz, 5G 10min./1 cycle,period for 60min. each along X,Y,Z axes | ||
| Safety&EMC | Safety standards | EN61347-1 EN61347-2-13 (EU) and UL8750 (US) | |
| Withstand voltage | I/P-O/P:3.75KVAC (EU) and I/P-O/P:1.88KVAC (US) | ||
| Isolation resistance | I/P-O/P:100M Ohms/500VDC/25℃/70%RH | ||
| EMC EMISSION | Compliance to EN55015, EN61000-3-2 (≥60%load) (EU) and FCC Part 15 (US) | ||
| EMC IMMUNITY | Compliance to EN61000-4-2,3,4,5,6,11, EN61547, light industry | ||
| Others | Net Weight | 0.25Kg | |
| Dimension | 300*30*18.5mm(L*W*H) | ||
| packing | 330*330*130mm/50PCS/CTN G.W.:13.6KG/CTN | ||
| Notes | 1. All parameters NOT specially mentioned are measured at 230VAC input , rated load and 25℃of ambient temperature. 2. Tolerance: includes set up tolerance, line regulation and load regulation . 3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. |
||
- Input terminal with Live Wire(L) , Neutral Wire (N)
- OutputLED SEC (LED+), output negative (LED). Connected to LED Lamps
■ Dimming wiring
- Dimming wires are installed for Dimming terminals (Nopolar) and are connected to the DALI BUS when use DALI function .
- wire (N) is connected to AC (N) while and wire (L) is connected to Push dim switch dimmer( L) when use Push function.
- Please make sure you connect these correctly otherwise your product will not function correctly and could be damaged.
