DMX512 Dim CV LED drivers 300w (IP67)
This dmx led driver is designed for dry, damp and wet location. The power factor of this driver is up to 0.9 and the efficiency is higher than 0.98. The height is 25mm, which is suitable for narrow space.
Model | SMT-12300-XC-A | SMT-24300-XC-A | |
X=1 , 2, 3, 4, 5 for DIM (DW); CCT(TW); RGB; RGBW; RGBW+CCT (RGBCW) | |||
Output | DC Voltage | 12V | 24V |
Voltage Tolerance | ±0.5V | ||
Voltage Regulation | ±0.5% | ||
Rated current | CH1+CH2+CH3+CH4+CH5=25A | CH1+CH2+CH3+CH4+CH5=12.5A | |
Rated power | 300W | ||
Load Regulation | ±1% | ||
Input | Voltage Range | 110-277VAC | |
Frequency Range | 47-63Hz | ||
PowerFactor(Typ.)@full load | PF≥0.98@230VAC | ||
THD(Typ.)@full load | ≤10% | ||
Efficiency(Typ.)@full load | 91.5%@230VAC | 93%@230VAC | |
AC Current(Max.) | 3.5A | 3.5A | |
Inrush Current (Typ.) | 48.5A (Twidth 164us measured at 50% I peak, COLD START, 230VAC) | ||
Leakage current | <0.50mA | ||
Protection | Short Circuit | Hiccup mode ,recovers automatically after fault condition is removed | |
Over Loading | ≤120% Hiccup mode ,recovers automatically after fault condition is removed | ||
Over temperature | 100℃±10℃ shut down o/p voltage, automatically recover after cooling. | ||
Environment | Working TEMP. | -40~+60℃ (see below derating curve) | |
Working Humidity | 20~95%RH, non-condensing | ||
Storage TEMP.Humidity | -40~+80℃,10~95%RH | ||
TEMP .coefficient | ±0.03%/℃(0~50℃) | ||
Vibration | 10~500Hz, 5G 10min./1 cycle,period for 60min. each along X,Y,Z axes | ||
Safety&EMC | Safety standards | EN61347-1 EN61347-2-13 (EU) & UL8750 UL1310 (US) | |
Withstand voltage | I/P-O/P:3.75KVAC I/P-FG:1.88KVAC O/P-FG:0.5KVAC (EU) & I/P-O/P:1.5KVAC(US) | ||
Isolation resistance | I/P-O/P:100MΩ/500VDC/25℃/70%RH | ||
EMC EMISSION | EN55015 EN61000-3-2 ,3-3 (EU) & FCC Part 15 B (US) (≥60% loading) | ||
EMC Immunity | EN61000-4-2,3,4,5,6,11, EN61547 | ||
Others | Net Weight | 1KG | |
Dimension | 277x78x25mm (LxWxH) | ||
packing | 10PCS/CTN | ||
Notes | 1. All parameters NOT specially mentioned are measured at 230VAC input , rated load and 25℃of ambient temperature. | ||
2. Tolerance: includes set up tolerance, line regulation and load regulation . | |||
3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. |
※Input Rubber cable 3*1.0mm²(VDE approval), the Y/G cable connect with (FG) , Brown with AC (L), Blue with AC(N) (EU)
Input SJOW Rubber cable 3*18AWG (UL approval), the green cable connect with (FG) ,Black with AC (L), White with AC(N) (US)
※Dimming cable: Purple (D+), Brown (D-) and Gray (GND) connect to DMX dimmer / system.
※Output cable to be connected to LED Light;
DIM (DW) dimming: Rubber cable
Black is output ( V+) Positive, White is output (V-) negative
CCT (TW) dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG
Black is output ( V+) Positive, While (CW-) and Yellow (WW-) are output (V-) negative
RGB dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG
Black is output ( V+) Positive, Red (R-), Green (G-) and Blue (B-) are output (V-) negative
RGBW dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG
Black is output ( V+) Positive, Red (R-), Green (G-) ,Blue (B-) , White (W-) are output (V-) negative
RGB+CCT dimming: 1015 electronic cable , (V+) 16AWG; (V-) 18AWG
Black is output ( V+) Positive, Red (R-), Green (G-) ,Blue (B-) , White (CW-) and Yellow (WW-) are output (V-) negative.;
※Please make sure you connect these correctly ,otherwise your product will not work correctly and could be damaged.
Note: there is external antenna at output side. Don't disassemble!
※The default address for the DMX driver is 001.
※Address settings device:
※Address settings:
① RDM setting address:
Set the address by the RDM device. For detailed operation, please refer to RDM device instruction manual.
② NFC setting address:
The DMX address can be read and written by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DMX512 driver.
■ Adjust output voltage Operation
※Adjust output voltage slightly for DMX512 driver
1) The driver output voltage can be read and written by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW) by close to the NFC signal area of the DMX512 driver.
2) Voltage range: level 1~10, each level is 0.2V. The default output voltage level is 5. Such as SMT-24030-XC-P, default is level 5 corresponding to 24V. By adjusting output voltage slightly, you could get 23.2v to 25V freely.
■ See figure below
Simple operation about DMX512 address reset and adjusting output voltage slighting by a mobile with Easy NFC APP or NFC handheld device (NFC read & write device: NFC-RW)